One-Deck Linear Drain wetroom kit

One sizes fits all foam cored wetroom floor former ready to fit on to a concrete or boarded timber floor. Trim on site to the size required complete with a high flow linear drain and tanking compound.

one deck wetroom kit
  • Trimmed to size on site - e.g. 1200 x 900, 1400 x 800, 900 x 900 - ANY SIZE!
  • Includes Purus 600mm or 800mm channel drain and tanking kit.
  • Single fall to drain (no envelope-angle tile cuts).
  • Suitable for timber or concrete floors.
  • Choice of three linear grid patterns
  • Made from extruded foam (not agglomerated styrene particles).
  • Density weight load of 30 Tons per square meter.
  • Tiny 25mm x 25mm tiles may be used.
  • Point loading per 25mm x 25mm tile is 18.7kgs.

See below for sizes available

Why our Foam Cored underlay is so special

We insist on extruded foam (not styrene balls)

Why density is important.

Our Underlay Wet floors and Tile Backer Boards are made from extruded foam (not agglomerated styrene particles). As a result the density weight loading is 30 tons per sq. metre. This may sound a lot, but gives us the confidence to permit use of tiny (25mm x 25mm) mosaic tiling. The maximum point load per tile is therefore 18.7Kg per 25mm x 25mm tile and customers can have total peace of mind that the tile will not sink into the underlay.

Note: Beware of competitor products with densities of 12 – 24 tons per sq. metre.


PCS wetrom former detail

Extra Tough Skin

Each side of the former is layered with a reinforcing mesh and covered in a continuous layer of polymer cement.

gradient one deck

One-Deck tray kits c/w Living Linear Drains

The unique Living Linear drain (BBA approved) with patented NOOD no-odour trap: should the trap dry up, no smells or odours are permitted to leak into the room. Perfect for hotels or hospitals.

Living linear drain oultlet optionsThe Living Linear Drain
Choose your Gully type. The standard is the 52mm deep, side outlet or to suit your waste pipe run select the optional 105mm deep side, end or vertical outlet.

The Trap is offset to the side of the drain to assist positioning waste pipes away from joists.

side view of living linear drain

  • Very high flow of water – 72 litres/minute (105mm options), 32 litres/minute (52mm option)
  • Mountings supplied for timber and concrete floors.
  • Accommodates tiles up to 10mm thick plus 3mm adhesive. Suitable for tiling only.
  • Tile insert or stainless steel designer grid options.
Standard Grid option for minimax

One-Deck foam cored wetroom deck with linear drain and TANKING kit contents:

1 - Foam cored One-Deck former .
1 - Purus channel drain (please specify your choice of outlet and grid)
1 - Pipe reducer 2” to 11⁄2” (50mm to 40mm).
1 - 8k tanking liquid (covers 10m2).
1 - 1 Litre Primer for porous surfaces.
1 - 10m Tape for wall/floor joint & other gaps.
2 - Internal corners.
2 - Pipe collars.
1 - 75mm brush.

Note: The Foam Cored wetroom kit is not suitable for use with vinyl flooring.

But unlike competitor kits it can be used with 25mm square mosaic tiles.

One-Deck Linear Wetroom Kit Deck - Cutting Schedule

Please Contact Us for prices and ordering.

The One Deck is designed to be cut down to size from the maximum 1200 x 1800mm.

The width can be cut down as required to the width of the drain, 600mm or 800mm, thesides can be cut equally or so the drain is offset to one side.

The length can be cut down from the rear of the drain and the main part so both sides are of the same thickness. the rear part can be removed entirely so the drain fits tight to a wall.

The diagrams below explain the how to cut to maintain equal thickness at each end.


one deck cutting instructions

Cutting Schedule for cutting to size

Example for 1400mm length. Refer to Drawing A and measure 67mm from the edge of the steep gradient and cut.

From there measure 1400 down the deck and cut to length (Drawing B).

The edge thickness will be 25-26mm.

Reduce the 1200mm width as required.

one deck cutting diagram a
one deck cutting diagram b